Bryant 575A Instrukcja Użytkownika Pobierz pdf

IMPORTANT — READ BEFORE INSTALLING

1. Read and become familiar with these installation in-

structions before installing this unit.

2. Be sure the installation conforms to all applicable local

and national codes.

3. These instructions contain important information for the

proper maintenance and repair of this equipment. Re-

tain these instructions for future use.

CONTENTS

Page

SAFETY CONSIDERATIONS .......................1

INSTALLATION .................................1-8

I. Complete Pre-Installation Checks ............1

II. Rig and Mount the Unit .....................3

III. Complete Refrigerant Piping Connections .....4

IV. Make Electrical Connections ................6

START-UP ....................................8-11

I. Preliminary Checks ........................8

II. Evacuate and Dehydrate ....................8

III. Refrigerant and Oil Charge ..................8

IV. Refrigerant Service Ports ...................9

V. Sequence of Operation .....................9

VI. Checking Cooling and Heating Control

Operation ...............................10

VII. Malfunction ..............................10

SERVICE ....................................11,12

I. Cleaning ................................11

II. Lubrication ..............................12

III. Outdoor Fan Adjustment ...................12

IV. Compressor Removal .....................12

TROUBLESHOOTING CHART ...................13,14

START-UP CHECKLIST .....................CL-1,CL-2

SAFETY CONSIDERATIONS

Installing and servicing air-conditioning equipment can be haz-

ardous due to system pressure and electrical components. Only

trained and qualiﬁed service personnel should install or serv-

ice air-conditioning equipment.

When working on air-conditioning equipment, observe pre-

cautions in literature and on tags and labels attached to unit.

Follow all safety codes. Wear safety glasses and work gloves.

Use quenching cloth for brazing operations. Have ﬁre extin-

guisher available. Read these instructions thoroughly. Con-

sult local building codes and National Electrical Code (NEC)

for special installation requirements.

WARNING:

Before installing or servicing system, al-

ways turn off main power to system. There may be more

than one disconnect switch. Electrical shock can cause

personal injury.

INSTALLATION

The 575A090 unit uses a semi-hermetic compressor. See

Table 1 for physical data.

The 575A090 outdoor unit is approved for use only with the

524A-H090 indoor unit. Use only approved indoor unit.

The 575A090 unit is Underwriters’Laboratories (UL) and UL

Canada approved for use with the 524A-H090 indoor unit only.

I. COMPLETE PREINSTALLATION CHECKS

A. Uncrate Unit (See Fig. 1)

Remove unit packaging except for the top skid assembly and

wood bumpers, which should be left in place until after unit

is rigged into place.

B. Inspect Shipment

File claim with shipping company if shipment is damaged or

incomplete.

C. Consider System Requirements

• Consult local building codes and NEC for special installa-

tion requirements.

• Allow sufficient space for airﬂow clearance, wiring, refrig-

erant piping, and servicing unit. See Fig. 2.

• Locate unit so that outdoor unit airﬂow is unrestricted on

all sides and above. Refer to Fig. 2.

• Unit may be mounted on a level pad directly on base rails

or mounted on raised pads at support points. See Fig. 2 for

weight distribution based on recommended support points.

• Provide for condensate drainage and defrost water dis-

posal beneath unit.

• Areas with high snowfall may need elevated mounting for

adequate airﬂow.

NOTE: If vibration isolators are required for a particular in-

stallation, use corner weight information in Fig. 2 to make

proper selection.

Fig. 1 — 575A090 Unit

installation, start-up

and service instructions

COMMERCIAL AIR-COOLED

SPLIT SYSTEM HEAT PUMP

575A

Size 090

⁄

Tons

Cancels: II 575A-90-1 II 575A-90-2

12/1/95

1 2 3 4 5 6 ... 15 16

Podsumowanie treści

Strona 1 - SPLIT SYSTEM HEAT PUMP

IMPORTANT — READ BEFORE INSTALLING1. Read and become familiar with these installation in-structions before installing this unit.2. Be sure the install

Strona 2 - Fig. 2 — Dimensions

C. DefrostDefrost board (DB) is a time and temperature control, whichincludes a ﬁeld-selectable time period between checks for frost(30, 50, and 90 mi

Strona 3

SERVICECAUTION:When servicing unit, shut off all electri-cal power to unit to avoid shock hazard or injury fromrotating parts.I. CLEANINGInspect unit

Strona 4

II. LUBRICATIONA. CompressorsCompressor has its own oil supply. Loss of oil due to a leak inthe system should be the only reason for adding oil after

Strona 5

TROUBLESHOOTING CHART, HEATING CYCLELEGENDN.C. — Normally Closed—13—

Strona 6

Strona 7 - Table 4 — Electrical Data

START-UP CHECKLISTI. PRELIMINARY INFORMATIONOUTDOOR: MODEL NO.INDOOR: MODEL NO.SERIAL NO.SERIAL NO.ADDITIONAL ACCESSORIESB. Pre-Start-UpOUTDOOR UNITIS

Strona 8

C. Start-UpCHECK INDOOR-FAN SPEED AND RECORD.CHECK OUTDOOR-FAN SPEED AND RECORD.AFTER AT LEAST 15 MINUTES RUNNING TIME, RECORD THE FOLLOWING MEASUREME

Strona 9

UNIT575AUNIT W/ALUMINUM-FINCOILUNIT W/COPPER-FINCOILWEIGHT (WITH ALUMINUM-FIN COIL) WEIGHT (WITH COPPER-FIN COIL)Std Unit Corner W Corner X Corner Y C

Strona 10

Table 1 — Physical DataUNIT 575A 090OPERATING WEIGHT (lb)Aluminum Coils (Standard) 540Copper Coils (Optional) 608RIGGING WEIGHT (lb)Aluminum Coils (St

Strona 11

III. COMPLETE REFRIGERANT PIPING CONNECTIONSSuction connection is sweat with plastic cap; liquid connec-tion is sweat with plastic cap. Refer to Table

Strona 12

LEGENDNEC — National Electrical CodeTXV — Thermostatic Expansion Valve*Accessory item.†Field supplied.NOTES:1. All piping must follow standard refrige

Strona 13 - N.C. — Normally Closed

IV. MAKE ELECTRICAL CONNECTIONSWARNING:Unit cabinet must have an uninterrupted,unbroken electrical ground to minimize the possibilityof personal injur

Strona 14

Table 4 — Electrical DataUNIT575ANOMINAL VOLTAGE(V-Ph-Hz)VOLTAGE RANGE COMPRESSOR OFM POWER SUPPLY MINIMUM DISCONNECTMin Max RLA LRA FLA MCAMAX FUSE O

Strona 15 - START-UP CHECKLIST

C. Field Control WiringInstall an approved accessory thermostat assembly accord-ing to installation instructions included with the accessory.Locate th

Strona 16 - C. Start-Up

B. Oil ChargingAllow unit to run for about 20 minutes. Stop unit and checkcompressor oil level. Add oil only if necessary to bring oil intoview in sig

Komentarze do niniejszej Instrukcji

Brak uwag

Bryant 575A Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Pompy Bryant 575A. Bryant 575A User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pompy Bryant 575A